View Cart
0 Items | Total: US$0.00
Welcome,      Register

You are here

RS0073 - UCS-E CIMC Configuration (Part 1)

Rating: 
5
Average: 5 (2 votes)
Difficulty Level: 
0
Lab Document: 
<Please login to see the content>
The video shows different interface options available, internal as well as external, to gain access to CIMC on Cisco UCS-E. The demonstration will be on EN120E and E140D UCS-E modules in ISR G2. The configuration will be compared to ISR 4K with their differences noted. We will then go through CIMC web interface and complete the remaining configuration.
 
Part 1 of this video covers CIMC interface configuration on EN120E
 
Topic:
  • UCS E-Series CIMC
  • UCS E-Series EN120N and E140D
  • UCS E-Series Interface GE0, GE1, GE2, GE3, and Dedicated Management
  • UCS E-Series on ISR G2 and 4K
  • CIMC Web Interface
  • UCS E-Series Router Commands

About Author

Metha Chiewanichakorn, CCIE#23585 (Ent. Infra, Sec, SP), is a Cisco networking enthusiast with years of experience in the industry. He is currently working as a consulting engineer for a Cisco partner. As a founder of and an instructor at labminutes.com, Metha enjoys learning and challenges himself with new technologies.

1 comments

I was configuring the CIMC IP. Below is the config I did for CIMC Access , method using the E-Series Server's ( UCS-E140S-M2/K9) Internal NIC GE1 and routers UCSE 1/0/1 Interface.

Physical Connectivity I did is connected a Cable to Routers GE0 Interface with a PC where I assigned a same block IP ( 10.7.29.210 ). From PC ( 10.7.29.210 ).

I can Ping G00/0/0 but not the CIMC IP ( 10.7.29.202 ). Also from Router I can Ping G0/0/0 IP but not CIMC IP. I also added "sh ip interface brief" , “ sh platform” command output in case it helps.

Can you advise what is wrong I am doing here ?

interface GigabitEthernet0/0/0
ip address 10.7.29.201 255.255.255.0
negotiation auto

interface ucse1/0/1
ip unnumbered GigabitEthernet0/0/0
no negotiation auto
switchport mode trunk

ucse subslot 1/0
imc access-port shared-lom console
imc ip address 10.7.29.202 255.255.255.0 default-gateway 10.7.29.201

ip route 10.7.29.202 255.255.255.255 ucse1/0/1

Command Output

Roter#sh ip interface brief

Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0/0 10.7.29.201 YES NVRAM up up
GigabitEthernet0/0/1 unassigned YES NVRAM administratively down down
GigabitEthernet0/0/2 unassigned YES NVRAM administratively down down
GigabitEthernet0/1/0 unassigned YES unset down down
GigabitEthernet0/1/1 unassigned YES unset down down
GigabitEthernet0/1/2 unassigned YES unset down down
GigabitEthernet0/1/3 unassigned YES unset down down
GigabitEthernet0/1/4 unassigned YES unset down down
GigabitEthernet0/1/5 unassigned YES unset down down
GigabitEthernet0/1/6 unassigned YES unset down down
GigabitEthernet0/1/7 unassigned YES unset down down
ucse1/0/0 unassigned YES NVRAM administratively down down
ucse1/0/1 10.7.29.201 YES unset up up
GigabitEthernet0 unassigned YES NVRAM administratively down down
Vlan1 unassigned YES NVRAM administratively down down

Router#ping 10.7.29.201
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.7.29.201, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms

Router#ping 10.7.29.202
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.7.29.202, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)

Poll

Vote for the Next Video Series